Gemini Industries CDX-02 Manuel d'utilisateur télécharger pdf (Page 4)

INTRODUCTION:

Congratulations on purchasing the Gemini CDX-02 Professional Dual

CD Player. This state of the art professional CD player is backed by a

three year warranty, excluding lasers. One year warranty on CD lasers.

Prior to use, we suggest that you carefully read all the instructions.

FEATURES:

· Large blue backlit LCD display

· Three-way time selection

· Single/auto-continuous play modes

· Beat per minute counter tap button

· Precise rubber jog wheels with finger grips

· Pitch bend with jog wheel or buttons

· Stutter play for accurate cue point selection

· Instant-start & cue with preview

· Fast track & song searching

· CD-R compatible

SAFETY CERTIFICATIONS:

Laser Diode Properties

Material: Ga - Al - As

Wavelength: 755 - 815 nm (25° C)

Laser Output: Continuous Wave, max. 0.5mW

CAUTIONS:

1. Do not use this CD Player at temperatures below 41°F/5°C or higher

than 95°F/35°C.

2. The apparatus should not be exposed to dripping or splashing and no

objects filled with liquids such as vases should be placed on the appara-

tus. Place the unit in a clean and dry location.

3. Do not place the unit in an unstable location.

4. When disconnecting the power cord from an AC outlet, always grasp

it by the plug. Never pull the power cord.

5. To prevent electric shock, do not remove the cover or the bottom

screws.

6. There are no user serviceable parts inside. Please refer servicing

to a qualified technician.

7. Do not use chemical solvents to clean the unit.

8. Keep the laser pickup clean by keeping the drawer closed.

9. Keep this manual in a safe place for future reference.

IMPORTANT NOTE:

Since the CDX-02 is a dual CD player, most of the functions and controls

are duplicated on both sides of the CD player. To eliminate confusion

and to make the drawings easier to understand, we will only number the

left side functions and controls.

LINE VOLTAGE SELECTION:

Model CDX-02 is a dual voltage unit. It will operate at 115 or 230 volts.

To set the proper voltage, follow these steps:

1. Place the head of a screwdriver in the center of the VOLTAGE

SELECTOR SWITCH (1) found on the rear panel.

2. Slide the switch to 115 or 230 volts.

3. Do not force or twist the switch. Excessive force may cause damage.

If the switch does not move smoothly, contact a qualified technician.

CONNECTIONS:

1. Connect the power plug into the AC IN (2).

2. Using the included cable, plug one end into the rear of the CONTROL

UNIT (3) and the other end into the MAIN UNIT (3)

3. Plug one end of a set of the included RCA cable connectors into each

of the LINE OUTPUT JACKS (4).

4. Plug the other end of the RCA connectors into any available line level

input jacks on your mixer. If you are connecting the CDX-02 through a

receiver, you can plug the RCA connectors into the CD or AUX INPUT

JACKS on your receiver. If there are no CD or AUX INPUTS, use any

line level (not phono) inputs.

FUNCTION DESCRIPTIONS:

POWER: After making sure that the VOLTAGE SELECTOR (1)

switch, found on the rear panel, is properly set, plug the unit in and press

the POWER (5) button. The unit will turn on. Pushing the POWER but-

ton (5) a second time will turn the unit off.

DISC TRAY: The DISC TRAY (7) is where the CD is held during load-

ing, unloading and playback. Pressing the OPEN/CLOSE (6 & 8) button,

will open or close the tray. The DISC TRAY (7) holds both 12 cm and 8

cm CDs. Please note, if the CDX-02 is in play mode, the tray will not

open.

Note: Do not force the DISC tray to close, excessive force will damage the CD mecha

nism, use the open/close (8) buttons only.

OPEN/CLOSE BUTTON: Press OPEN/CLOSE (6 & 8) to load or

remove a CD from the DISC TRAY.

L.C.D.: The LIQUID CRYSTAL DISPLAY (12) shows the track number,

pitch value, single-auto cue, continue (for continuous play), and 4 differ-

ent time displays. These time displays are time elapsed on the track,

time remaining on the disc, the last 30 second outro of the track, and

time remaining on the track. Time is measured in minutes, seconds and

frames.

PLAYBACK DISPLAY BAR: The PLAYBACK DISPLAY BAR (13) dis-

plays the elapsed and remaining time for each track. The display flashes

slowly when the track has 30 seconds remaining and pulses rapidly

when playing time is down to 15 seconds.

PLAY/PAUSE: Each press of the PLAY/PAUSE BUTTON (10)

causes the operation to change from play to pause or from pause back

to play.

CUE: With the unit in the PLAY mode (PLAY/PAUSE LED is green) and

after the cue point has been programmed, pressing CUE (11) will imme-

diately pause the track at the programmed CUE point (the CUE LED

glows blue). In PAUSE mode(PLAY/PAUSE LED blinks), holding down

CUE (11) changes the function to preview and starts the CD from the

programmed cue point. Releasing the CUE (11) button will return the CD

laser to the preset cue point in PAUSE mode.

BPM: Tapping the BPM (23) button allows you to count the beats per

minute on a track. Holding the BPM (23) switches display modes from

BPM to PITCH, which is indicated on the right side of the LCD (12).

TRACK SKIP: The TRACK SKIP (14) buttons let you select the

track to play.

+10: The +10 (15) button lets you quickly scan through track numbers in

increments of ten.

SEARCH JOG WHEEL: Use the SEARCH JOG WHEEL (9) to select

the scanning direction and speed of your CD. Turning the wheel in a

clockwise direction scans forward while a counter-clockwise turn scans

the track in reverse. Scan speed increases as the wheel is turned.

SEARCH DIAL: The SEARCH DIAL (9) has two functions. Use the

SEARCH DIAL (9) to make fine adjustments in pause mode. Use the

SEARCH DIAL (9) to bend the pitch for precise synchronization in play

mode.

SEARCH: The SEARCH (16) buttons are used to move for-

ward or reverse while in play or pause mode, SEARCH (16) can also be

used to find a CUE POINT. Hold down either button for ultra fast

searching.

STOP : The STOP (18) button ends CD play.

SINGLE:

Pressing the SINGLE (19) activates the AUTO CUE function.

The AUTO CUE function causes the unit to pause at the beginning of

music of the following track and allows you to start play immediately from

the start of music without any blank space (which exists at the beginning

of every track). Pressing the SINGLE (19) button a second time activates

(4)

1 2 3 4 5 6 7 8 9 10 11 12

Commentaires sur ces manuels

Pas de commentaire

Gemini Industries CDX-02 Manuel d'utilisateur Page 4

Commentaires sur ces manuels